Millennium EPDM Flashing Tapes consist of an uncured EPDM membrane that has been laminated to a 25 mil EPDM based pressure sensitive tape adhesive. The fl ashing tape is extremely flexible and can be formed to fi t irregular shapes and surfaces.

Basic Use
Millennium EPDM Flashing Tapes are ideal for flashing rooftop penetrations and other details such as:
  • Overlay at T-joints, corners, pipes, and penetrations
  • General repair in non-traffic areas
  • Gravel stop flashing
  • General purpose flashing
  • Metal edge tie-in
Request Information
Unit of Measure
Items
Millennium EPDM Flashing Tape

Millennium EPDM 5" Flashing Tape
Millennium EPDM Flashing Tape

Millennium EPDM 6" Flashing Tape
Millennium EPDM Flashing Tape

Millennium EPDM 9" Flashing Tape
Millennium EPDM Flashing Tape

Millennium EPDM 12" Flashing Tape
Description N/A Millennium EPDM Flashing Tapes consist of an uncured EPDM membrane that has been laminated to a 25 mil EPDM based pressure sensitive tape adhesive. The fl ashing tape is extremely flexible and can be formed to fi t irregular shapes and surfaces.

Basic Use
Millennium EPDM Flashing Tapes are ideal for flashing rooftop penetrations and other details such as:
  • Overlay at T-joints, corners, pipes, and penetrations
  • General repair in non-traffic areas
  • Gravel stop flashing
  • General purpose flashing
  • Metal edge tie-in
 		N/A Millennium EPDM Flashing Tapes consist of an uncured EPDM membrane that has been laminated to a 25 mil EPDM based pressure sensitive tape adhesive. The fl ashing tape is extremely flexible and can be formed to fi t irregular shapes and surfaces.

Basic Use 		N/A Millennium EPDM Flashing Tapes are ideal for flashing rooftop penetrations and other details such as:
  • Overlay at T-joints, corners, pipes, and penetrations
  • General repair in non-traffic areas
  • Gravel stop flashing
  • General purpose flashing
  • Metal edge tie-in
 		N/A Millennium EPDM Flashing Tapes consist of an uncured EPDM membrane that has been laminated to a 25 mil EPDM based pressure sensitive tape adhesive. The fl ashing tape is extremely flexible and can be formed to fi t irregular shapes and surfaces.

Basic Use Millennium EPDM Flashing Tapes are ideal for flashing rooftop penetrations and other details such as:
  • Overlay at T-joints, corners, pipes, and penetrations
  • General repair in non-traffic areas
  • Gravel stop flashing
  • General purpose flashing
  • Metal edge tie-in
Surface Preparation N/A All work surfaces should be clean, dry, and free of dirt, dust, debris, oils, un-adhered coatings, deteriorated membrane and other contaminants that may result in a surface that is not sound or is uneven. If necessary, clean the surface to receive the fl ashing with an approved EPDM membrane cleaner.
Safety N/A Prior to working with this or any product consult product label and Material Safety Data Sheet (MSDS) for necessary health and safety precautions.
Limitations N/A
  • Not for use on PVC roof membranes.
  • Not for use in high traffic areas.
  • Talc, dust, oil, ice, snow, or wet conditions inhibit good adhesion. Clean and dry surfaces are necessary for proper installation of this product.
Color N/A Black
Packaging & Coverage N/A Millennium EPDM Flashing Tape is available in the following sizes:
Width N/A 5 "127 mm N/A 6 "152 mm N/A 9 "229 mm N/A 12 "305 mm
Rolls/Case N/A 2 N/A 2 N/A 2 N/A 1
Storage and Shelf Life N/A Store material in original unopened packaging at temperatures between 40°F-110°F. Shelf life is 9 months when stored as recommended.
Applications N/A
  1. Clean entire surface where Millennium EPDM Flashing Tape will be applied.
  2. Apply EPDM primer to entire surface to be covered using the supplied scrub pad. NOTE: Use caution when installing at temperatures below 40oF (5oC) to prevent blushing of EPDM primer (formation of condensation on surface of primer).
  3. Allow the primer to dry to the touch (no material transfer, typically less than 20 minutes). Dry time will vary depending on ambient temperature and humidity.
  4. Once the primer is dry immediately install Millennium EPDM Flashing Tape.
  5. Position Flashing Tape over primed area and remove release liner. Press down and form Flashing Tape by hand.
  6. Roll the flashing with a 2” (5.08cm) wide silicone roller.
  7. Seal edges of flashing detail with Millennium EPDM Edge Sealant.
Technical Data N/A
Typical Physical Properties and Characteristics
  Typical Values Test Method
Base Polymer (Flashing & Tape) EPDM FTIR
Color (Flashing & Tape) Black Visual
Tensile Strength (uncured) 250 psi max. ASTM D412 Die C
Benefits N/A Flashing details with proven peel-n-stick technology Improved safety Long-term durability Saves time and labor Suitable for roofing or waterproofing applications
Note N/A The foregoing information is published as general information only. The listed properties and performance characteristics are typical values and are not to be interpreted as manufacturing specifications.
Features N/A Excellent adhesion and formability Fast installation No torch or liquid adhesives Resistant to UV light, high heat and moisture Waterproof detail
Length N/A 100 '30.48 m N/A 100 '30.48 m N/A 50 '15.24 m N/A 50 '15.24 m

our Mission

Our goal is to maximize growth in the construction industry by providing the best customer support possible. Our tools to achieve this goal are the proper selection of quality products delivered on time, with in-house service of all products supplied, and committed dedicated employees.

We measure our success by satisfied customers and employees embracing the mission.

BBB | Accreited Business

Testimonials> Locations> Contact>