Atlantic Equipment
Atlantic Equipment
146 Railroad Avenue
Revere, MA 33009
Phone: (800) 543-3350 • Local: (781) 289-6788 • Fax: (954) 457-8559
Email: info@atlanticasphalt.com
Print Back
Millennium EPDM Cover Strip consists of a semi-cured EPDM membrane that has been laminated to a 25 mil EPDM based pressure sensitive tape adhesive.

Basic Use
Millennium EPDM Cover Strips are designed to cover, protect, and seal mechanical fastening bars, membrane fasteners, core sample repair patches, membrane repairs, and seam overlays in all EPDM roofing systems.
Millennium EPDM Cover Strip 3
Millennium EPDM Cover Strip 4
Unit of Measure
Items Millennium EPDM Cover Strip 3
ET-0911-06CC
Millennium EPDM 6" Cover Strip 		Millennium EPDM Cover Strip 3
ET-0911-09CC
Millennium EPDM 9" Cover Strip 		Millennium EPDM Cover Strip 3
ET-0911-12CC
Millennium EPDM 12" Cover Strip 		Millennium EPDM Cover Strip 3
ET-0911-05CC
Millennium EPDM 5" Cover Strip
Description N/A Millennium EPDM Cover Strip consists of a semi-cured EPDM membrane that has been laminated to a 25 mil EPDM based pressure sensitive tape adhesive.

Basic Use
Millennium EPDM Cover Strips are designed to cover, protect, and seal mechanical fastening bars, membrane fasteners, core sample repair patches, membrane repairs, and seam overlays in all EPDM roofing systems. 		N/A Millennium EPDM Cover Strip consists of a semi-cured EPDM membrane that has been laminated to a 25 mil EPDM based pressure sensitive tape adhesive.

Basic Use
Millennium EPDM Cover Strips are designed to cover, protect, and seal mechanical fastening bars, membrane fasteners, core sample repair patches, membrane repairs, and seam overlays in all EPDM roofing systems. 		N/A Millennium EPDM Cover Strip consists of a semi-cured EPDM membrane that has been laminated to a 25 mil EPDM based pressure sensitive tape adhesive.

Basic Use
Millennium EPDM Cover Strips are designed to cover, protect, and seal mechanical fastening bars, membrane fasteners, core sample repair patches, membrane repairs, and seam overlays in all EPDM roofing systems. 		N/A Millennium EPDM Cover Strip consists of a semi-cured EPDM membrane that has been laminated to a 25 mil EPDM based pressure sensitive tape adhesive. 

Basic Use
Millennium EPDM Cover Strips are designed to cover, protect, and seal mechanical fastening bars, membrane fasteners, core sample repair patches, membrane repairs, and seam overlays in all EPDM roofing systems.
Surface Preparation N/A All work surfaces should be clean, dry, and free of dirt, dust, debris, oils, un-adhered coatings, deteriorated membrane and other contaminants that may result in a surface that is not sound or is uneven. If necessary, clean the surface to receive cover with an approved EPDM membrane cleaner.
Safety N/A Prior to working with this or any product consult product label and Material Safety Data Sheet (MSDS) for necessary health and safety precautions.
Limitations N/A
  • Not for use on PVC roof membranes.
  • Do not use for detail fl ashing applications.
  • Talc, dust, oil, ice, snow, or wet conditions inhibit good adhesion. Clean and dry surfaces are necessary for proper installation of this product.
Color N/A Black
Packaging & Coverage N/A Millennium EPDM Cover Strip is available in the following sizes:
Width N/A 6 "152 mm N/A 9 "229 mm N/A 12 "305 mm N/A 5 "127 mm
Rolls/Case N/A 2 N/A 1 N/A 1 N/A 2
Storage and Shelf Life N/A Store material in original unopened packaging at temperatures between 40 °F-110 °F. Shelf life is 12 months when stored as recommended.
Applications N/A
  1. Clean entire surface where Millennium EPDM Cover Strip will be applied.
  2. Apply EPDM primer to entire surface to be covered using the supplied scrub pad. NOTE: Use caution when installing at temperatures below 40 ºF (5 ºC) to prevent blushing of EPDM primer (formation of condensation on surface of primer).
  3. Allow the primer to dry to the touch (no material transfer, typically less than 20 minutes). Dry time will vary depending on ambient temperature and humidity.
  4. Once the primer is dry immediately install Millennium EPDM Cover Strip.
  5. Position Cover Strip over primed area and remove release liner at 45 degree angle while pressing down cover strip by hand.
  6. Roll the Cover Strip with a 2” (5.08cm) wide silicone roller.
  7. Seal edges of cover detail with Millennium EPDM Edge Sealant.
Technical Data N/A
Typical Physical Properties and Characteristics
  Typical Values Test Method
Base Polymer(Cover & Tape) EPDM FTIR
Color (Cover & Tape) Black Visual
Tensile Strength 900 psi min. ASTM D412 Die C
Elongation 300% ASTM D412
Tear Resistance 125 lbs./in ASTM D624
Ozone Resistance No Cracking ASTM D4419
Peel Strength 10 pli @ 70 ºF ASTM D413
Shear Strength 20 psi @ 70 ºF ASTM D816
Brittleness Temperature -50 ºF ASTM D2137
Benefits N/A Improved safety Long-term durability Saves time and labor Suitable for a wide variety of sealing applications Suitable for roofing, pond lining, and waterproofing applications
Note N/A The foregoing information is published as general information only. The listed properties and performance characteristics are typical values and are not to be interpreted as manufacturing specifications.
Features N/A Excellent adhesion to multiple substrates Fast installation No torch or liquid adhesives Resistant to UV light, high heat and moisture Waterproof detail N/A Excellent adhesion to multiple substrates Fast installation No torch or liquid adhesives Resistant to UV light, high heat and moisture Waterproof detail N/A Excellent adhesion to multiple substrates Fast installation No torch or liquid adhesives Resistant to UV light, high heat and moisture Waterproof detail N/A Excellent adhesion to multiple substrates Fast installation No torch or liquid adhesives Waterproof detail
Length N/A 100 '30.48 m N/A 100 '30.48 m N/A 50 '15.24 m N/A 100 30.48